
【国外标准】 Standard Test Method for Evaluating Hygrothermal Corrosion Resistance of Permanent Magnet Alloys
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 This test method provides a controlled corrosive environment which can be utilized to produce relative corrosion resistance information for sintered permanent magnets.5.2 Although prediction of performance in natural environments has seldom been statistically correlated with corrosion test results, sufficient empirical results are available to support the usefulness of this test in quantifying relative resistance to corrosion from moisture and heat.5.3 The reproducibility of results in this test method is dependent on the type, size, and shape of specimens tested, and the control of the operating variables. In any testing program, sufficient replicates should be included to establish confidence limits. Replicates may be run simultaneously, in subsequent test runs, or in duplicate test chambers.5.4 When multiple test chambers and operators are utilized, efforts shall be made to perform a suitable repeatability and reproducibility study for the equipment, operators, and test method.1.1 This test method covers the equipment, procedures, and measurement of the resistance of permanent magnet alloys against corrosion in high temperature, high pressure water vapor environments. This test is also known as the Bulk Corrosion Test (BCT).1.2 The values and equations stated in customary (cgs-emu and inch-pound) units or SI units are to be regarded separately as standard. Within this standard the SI units, when different from customary units, are shown in brackets, the values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM A1071/A1071M-11(2023)
标准名称:
Standard Test Method for Evaluating Hygrothermal Corrosion Resistance of Permanent Magnet Alloys
英文名称:
Standard Test Method for Evaluating Hygrothermal Corrosion Resistance of Permanent Magnet Alloys标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- AS/NZS 1635.11.1:1995 Methods of test for pressure-sensitive adhesive tape - Water vapour transmission rate
- AS/NZS 2023:1995 Baths for ablutionary purposes
- AS/NZS 2891.11:2014 Methods of sampling and testing asphalt Degree of particle coating
- AS/NZS 3200.2.11:1999 Medical electrical equipment Particular requirements for safety - Gamma beam therapy equipment
- AS/NZS 3350.2.11:1995/Amdt 1:1998 Approval and test specification - Safety of household and similar electrical appliances - Particular requirements - Tumbler dryers
- AS/NZS 3350.2.11:1999/Amdt 2:2001 Safety of household and similar electrical appliances - Particular requirements - Tumble dryers
- AS/NZS 3350.2.11:2001/Amdt 1:2007 Safety of household and similar electrical appliances Particular requirements for tumble dryers (IEC 60335-2-11:2000, MOD)
- AS/NZS 4456.11:1997 Masonry units and segmental pavers - Methods of test Determining coefficients of expansion
- AS/NZS 4456.11:2003/Amdt 1:2004 Masonry units, segmental pavers and flags - Methods of test Determining coefficients of expansion
- AS/NZS 60079.11:2000/Amdt 1:2001 Electrical apparatus for explosive gas atmospheres Intrinsic safety 'i'
- AS/NZS 60335.2.11:2002/Amdt 1:2004 Household and similar electrical appliances - Safety - Particular requirements for tumble dryers (IEC 60335-2-11 Ed 6, MOD)
- AS/NZS 60695.11.20:2001/Amdt 1:2004 Fire hazard testing Test flames - 500 W flame test methods
- AS/NZS 60695.11.3:2001 Fire hazard testing Test flames - 500 W flames - Apparatus and confirmational test methods (IEC 60695-11-3:2000, IDT)
- AS/NZS 60695.2.11:2001/Amdt 1:2001 Fire hazard testing Glowing/hot wire based test methods - Glow-wire flammability test method for end-products
- AS/NZS 60745.2.11:2003 Hand-held motor-operated electric tools - Safety - Particular requirements for reciprocating saws