
【国外标准】 IEEE Standard Requirements for the Control of Electromagnetic Interference Characteristics of Replaceable Electronic Modules
本网站 发布时间:
2025-04-28
- IEEE 1688-2015
- 定价: 158元 / 折扣价: 135 元
- 在线阅读

适用范围:
This standard establishes interface and associated verification requirements for the control of the electromagnetic interference (emission and susceptibility) characteristics of replaceable electronic modules. Such equipment is used only as an integral part of other subsystems or systems, and may not be used independently. This standard is best suited for items that have the following features: removable/replaceable electronic circuit card modules that plug into an equipment rack or frame, with… read more electrical interconnections primarily through edge connectors that interface directly with a backplane, and electrical power input derived from the backplane power sources. This standard should not be directly applied to equipment that can be used independently as a stand-alone system or subsystem (separate box intra-connected by a wire harness to other boxes of a subsystem), or to entire system platforms. It is assumed that the rack/frame equipment with its full complement of REMs is tested in some configuration to an equipment EMI standard such as MIL-STD-461E. This standard is best suited for situations where the qualification of the REM is more effective than requalification of the rack/frame equipment with the new REM. read less
标准号:
IEEE 1688-2015
标准名称:
IEEE Standard Requirements for the Control of Electromagnetic Interference Characteristics of Replaceable Electronic Modules
英文名称:
标准状态:
-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM E1688-19 Standard Guide for Determination of the Bioaccumulation of Sediment-Associated Contaminants by Benthic Invertebrates
- ASTM E259-06(2015) Standard Practice for Preparation of Pressed Powder White Reflectance Factor Transfer Standards for Hemispherical and Bi-Directional Geometries
- ASTM E2752-10(2015) Standard Guide for Evaluation of Residual Effectiveness of Antibacterial Personal Cleansing Products
- ASTM E2784-10(2015) Standard Test Method for Evaluation of the Effectiveness of Handwash Formulations Using the Paper Towel (Palmar) Method of Hand Contamination
- ASTM F1035-03(2015) Standard Practice for Use of Rubber-Cord Pie Disk to Demonstrate the Discernment Capability of a Tire X-ray Imaging System
- ASTM F2255-05(2015) Standard Test Method for Strength Properties of Tissue Adhesives in Lap-Shear by Tension Loading
- ASTM F2258-05(2015) Standard Test Method for Strength Properties of Tissue Adhesives in Tension
- ASTM F2392-04(2015) Standard Test Method for Burst Strength of Surgical Sealants
- ASTM F2819-10(2015)e2 Standard Test Methods for Measurement of Straightness of Bar, Rod, Tubing and Wire to be used for Medical Devices
- ASTM F665-09(2015) Standard Classification for Vinyl Chloride Plastics Used in Biomedical Application
- ASTM F754-08(2015) Standard Specification for Implantable Polytetrafluoroethylene (PTFE) Sheet, Tube, and Rod Shapes Fabricated from Granular Molding Powders
- ASTM D2505-88(2015) Standard Test Method for Ethylene, Other Hydrocarbons, and Carbon Dioxide in High-Purity Ethylene by Gas Chromatography
- ASTM F602-09(2015) Standard Criteria for Implantable Thermoset Epoxy Plastics
- ASTM F665-09(2015) Standard Classification for Vinyl Chloride Plastics Used in Biomedical Application
- ASTM F754-08(2015) Standard Specification for Implantable Polytetrafluoroethylene (PTFE) Sheet, Tube, and Rod Shapes Fabricated from Granular Molding Powders