【国外标准】 Standard Specification for Cast Iron Soil Pipe and Fittings

This specification covers cast gray iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. These pipe and fittings are not intended for pressure applications. The cast iron shall be produced by an established commercial method that provides control over chemical and physical properties. Castings shall be sound, true to pattern, and of compact close grain that permits drilling and cutting by ordinary methods and its interior surface shall be reasonably smooth and free from defects. Ferrous scrap, pig iron, and any recycled ferrous material to be used in the melting operation shall be screened for radioactivity. Tension test shall include breaking load, machined diameter, and tensile strength. Chemical test shall conform to the chemical composition requirements prescribed for phosphorous, sulfur, chromium, titanium, aluminum, lead, and carbon equivalent. Dimension requirements for hub, spigot, barrel, grooves, water seal and trap, and threads of the pipe and fittings are detailed. The pipe and fittings shall be uniformly coated with a material suitable for the purpose.1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. It establishes standards covering material, manufacture, mechanical and chemical properties, coating, test methods, inspection, certification, product markings, dimensions, and dimensional tolerances for extra-heavy and service cast iron soil pipe and fittings. These pipe and fittings are not intended for pressure applications as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.1.2 This specification covers pipe and fittings of the following patterns and, when so designated, shall apply to any other patterns that conform with the dimensions found in Tables 1 and 2 and all other applicable requirements given in this specification.1.2.1 Pipe:  TablesExtra heavy, 21/2 ft (0.75 m), 31/2 ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m) lengths 1, 2Service, 21/2 ft (0.75 m), 31/2 ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m) 1, 2Outside dimensions (for detailing) X1.11.2.2 Fittings:  Tables1/4 bends; long 1/4 bends 3, 41/4 bends, long low-hub 51/4 bends, low heel; high heel 6, 71/4 bends, short sweep; long sweep 81/4 bends, reducing long sweep 91/5 bends 101/6 bends 101/8 bends; long 1/8 bends 111/16 bends 11Y branches 12, 13Y branches, combination 1/8 bends, single 14Y branches, combination 1/8 bends, double 14Sanitary T branches, single 15Sanitary T branches, double 15Sanitary T branches, cleanout 16Tapped sanitary T branches, single 17Tapped sanitary T branches, double 17T branches, single and double 18Tapped T branches, single 19Tapped T branches, double 19T branches, cleanout 20-45° offset fitting 21Double hubs 22Long double hubs 22Reducers 23Increasers 24, 25P traps 26, 27Deep seal P traps 28Running traps 29Screw plugs (brass) 30Blind plugs 31Iron-body ferrules 32Side inlets Fig. 3Closet bends 33Tapping bosses 34Reducing 1/4 bend SV 35Combination Y and 1/8 bend 36‘H’ branch fitting 371.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.