
【国外标准】 Standard Test Methods for Saponification Number of Pine Chemical Products Including Tall Oil and Other Related Products
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
3.1 These test methods are designed to broaden the scope of the earlier editions of the test method by the inclusion of tall oil and tall oil derived products as test materials and is referenced in Test Methods D803.3.2 The saponification number is an important property of tall oil and the products obtained by the fractionation of tall oil. It is the test method widely used to determine the total acid content, both free and combined, of these products.3.3 The potentiometric test method should be used when the most reproducible results are required.1.1 These test methods cover the determination of the saponification number of tall oil and products obtained by the fractionation of tall oil such as rosin, fatty acids and distilled tall oil as defined in Terminology D804. These test methods are also applicable to gum and wood rosin. Two test methods are covered as follows:1.1.1 Test method using a potentiometric method, and1.1.2 Test method using an internal indicator method.1.2 The potentiometric method is suitable for use with both light- and dark-colored test samples. It should be considered the referee method. The internal indicator method is suitable for use only with light- and medium-colored test samples. It should be considered the alternate method.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D464-15(2020)
标准名称:
Standard Test Methods for Saponification Number of Pine Chemical Products Including Tall Oil and Other Related Products
英文名称:
Standard Test Methods for Saponification Number of Pine Chemical Products Including Tall Oil and Other Related Products标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D4619-12(2018) Standard Practice for Inspection of Linings in Operating Flue Gas Desulfurization Systems
- ASTM D4623-16 Standard Test Method for Determination of In Situ Stress in Rock Mass by Overcoring Method—Three Component Borehole Deformation Gauge
- ASTM D4625-21 Standard Test Method for Middle Distillate Fuel Storage Stability at 43 °C (110 °F)
- ASTM D4626-23 Standard Practice for Calculation of Gas Chromatographic Response Factors
- ASTM D4630-19 Standard Test Method for Determining Transmissivity and Storage Coefficient of Low-Permeability Rocks by In Situ Measurements Using the Constant Head Injection Test
- ASTM D4631-18 Standard Test Method for Determining Transmissivity and Storativity of Low Permeability Rocks by In Situ Measurements Using Pressure Pulse Technique
- ASTM D4634-16(2022) Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA)
- ASTM D4636-17 Standard Test Method for Corrosiveness and Oxidation Stability of Hydraulic Oils, Aircraft Turbine Engine Lubricants, and Other Highly Refined Oils
- ASTM D4637/D4637M-15(2021)e1 Standard Specification for EPDM Sheet Used in Single-Ply Roof Membrane
- ASTM D4638-16(2023) Standard Guide for Preparation of Biological Samples for Inorganic Chemical Analysis
- ASTM D464-15(2020) Standard Test Methods for Saponification Number of Pine Chemical Products Including Tall Oil and Other Related Products
- ASTM D4647/D4647M-13(2020) Standard Test Methods for Identification and Classification of Dispersive Clay Soils by the Pinhole Test
- ASTM D465-15(2020) Standard Test Methods for Acid Number of Pine Chemical Products Including Tall Oil and Other Related Products
- ASTM D4651-14(2020) Standard Specification for Isobutane Thermophysical Property Tables
- ASTM D4653-87(2020) Standard Test Method for Total Chlorides in Leather