
【国外标准】 Standard Test Methods for Polymeric Films Used for Electrical Insulation
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
6.1 Many electrical and physical properties of films vary significantly with changes in temperature and humidity. Properties of thin plastic films can change very rapidly; therefore, the specimen needs to be in the stated conditioning environment when the test is being performed. When the test is performed in a different environment, note these conditions and the time of exposure to this new environment.1.1 These test methods cover the testing of homogeneous organic polymer films not over 2.4 mm (95 mils) thick that are to be used for electrical insulation.1.2 These test methods are not necessarily applicable to testing films in combinations with a coating, another film, or with other types of substrate, such as fabrics or papers.1.3 The values stated in SI units are the standard. The values in parentheses are provided for information only.1.4 The procedures appear in the following sections:Procedure SectionsConditioning 6 and 7Dielectric Breakdown Voltage & Dielectric Strength 21 to 26Extractables 65 to 70Heat-Seal Strength 59 to 64Permittivity and Dissipation Factor 42 to 47Resistance Method for Measuring the Tendency to Corrode Metals 38 to 41Sampling 5Shrinkage 48 to 53Strain Relief 13 to 20Surface Resistivity 27 to 31Tensile Properties 12Thickness 8 to 11Volume Resistivity 32 to 37Water Absorption 53 to 581.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: These test methods are similar to IEC 60674–2.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D2305-18
标准名称:
Standard Test Methods for Polymeric Films Used for Electrical Insulation
英文名称:
Standard Test Methods for Polymeric Films Used for Electrical Insulation标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- INCITS/ISO/IEC 23000-18:2018 (2021) Information technology - Multimedia application formats (MPEG-A) - Part 18: Media linking application format
- ASTM D8137-18(2023) Practice for Accelerated Aging of Leather
- ASTM D8138-23 Standard Specification for Preformed Silicone Joint Sealing System for Bridges
- ASTM D8139-23 Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction
- ASTM D814-95(2020) Standard Test Method for Rubber Property—Vapor Transmission of Volatile Liquids
- ASTM D8140-18(2023) Standard Guide for the Use of Foundry Sand in Asphalt Mixtures
- ASTM D8141-22 Standard Guide for Selecting Volatile Organic Compounds (VOCs) and Semi-Volatile Organic Compounds (SVOCs) Emission Testing Methods to Determine Emission Parameters for Modeling of Indoor Environments
- ASTM D8144-22 Standard Test Method for Separation and Determination of Aromatics, Nonaromatics, and FAME Fractions in Middle Distillates by Solid-Phase Extraction and Gas Chromatography
- ASTM D8148-22 Standard Test Method for Spectroscopic Determination of Haze in Fuels
- ASTM D8149-20 Standard Practice for Optimization, Calibration, and Validation of Ion Chromatographic Determination of Heteroatoms and Anions in Petroleum Products and Lubricants
- ASTM D8150-22 Standard Test Method for Determination of Organic Chloride Content in Crude Oil by Distillation Followed by Detection Using Combustion Ion Chromatography
- ASTM D8152-18 Standard Practice for Measuring Field Infiltration Rate and Calculating Field Hydraulic Conductivity Using the Modified Philip Dunne Infiltrometer Test
- ASTM D8154-24 Standard Test Methods for 1H-NMR Determination of Ketone-Ethylene-Ester and Polyvinyl Chloride Contents in KEE-PVC Roofing Fabrics
- ASTM D8155-17(2023) Standard Practice for Shake Extraction of Solid Mining and Metallurgical Processing Waste with Water
- ASTM D816-06(2023) Standard Test Methods for Rubber Cements