
【国外标准】 Standard Test Method for Bend Testing of Metallic-Coated Steel Sheet to Evaluate Coating Adhesion
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
4.1 This test method provides a standard method to bend the product to verify good coating, adhesion free of delamination, on metallic-coated steel sheet products under the jurisdiction of ASTM Committee A05 and its subcommittees as designated by a purchaser in a purchase order or contract.4.1.1 Metallic coated coupons are bent 180° around progressively more thicknesses of metal, the end point being when failures no longer occur. The bend area is examined without magnification after each bend in order to determine coating fracture and loss of adhesion.4.1.2 If desired, further examination of loss of adhesion or pickoff can be determined by performing a tape pull-off test subsequent to bending.4.1.3 The material condition at the time of testing, sampling frequency, specimen location and orientation, minimum t-bend rating exhibiting no delamination or pick-off, reporting requirements, and other test parameters are contained in the pertinent material specification or in a general requirement specification for the particular product form. References are provided to the appropriate ASTM standards.4.2 For this test method to successfully evaluate coating adhesion, the metal substrate must be capable of withstanding the bending operation without fracturing.4.3 Coating adhesion is a significant quality characteristic of metallic coated steel sheet products. This test method employs the relevant t-bend rating specified in the referenced product standards to quickly determine if the metallic coating is free of delamination on the outside of a bend specimen. This is critical in ascertaining product conformance to specifications.4.4 This test method is similar to, and uses some of the same apparatus as, Test Method D4145, which determines a t-bend rating for flexibility and adhesion of organic coatings (paints) on metallic substrates.4.5 This test method may be used by other ASTM Committees and other standards writing bodies for the purpose of conformance testing.1.1 This test method covers a bend test to verify that metallic coatings on steel sheet are free of delamination. The test method described is designed and intended for use in both laboratory and plant situations and their environments.1.2 The metallic-coated steel product shall conform to all the requirements of the appropriate specifications as follows: Specifications A463/A463M, A653/A653M, A755/A755M, A792/A792M, A875/A875M, A924/A924M, A929/A929M, A1046/A1046M, A1057/A1057M, A1063/A1063M, A1079, and A1087/A1087M.1.3 Quantitative limits are not addressed and are established in the general requirements, or individual product specifications, or both; or when applicable, as agreed to between supplier and user.1.4 Units—This specification is applicable to orders in either inch-pound units or SI units. Values in inch-pound and SI units are not necessarily equivalent. Within the text, SI units are shown in brackets. Each system shall be used independently of the other.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM A1122/A1122M-22
标准名称:
Standard Test Method for Bend Testing of Metallic-Coated Steel Sheet to Evaluate Coating Adhesion
英文名称:
Standard Test Method for Bend Testing of Metallic-Coated Steel Sheet to Evaluate Coating Adhesion标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 上一篇: ASTM A1120/A1120M-21 Standard Specification for Electric-Resistance-Welded Carbon Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes with Textured Surface
- 下一篇: ASTM A1123/A1123M-22 Standard Specification for Carbon Steel Laser and Laser-Hybrid Welded, Sharp-Cornered Profile (SCP), Built-Up, Square, Rectangular, and Special Shape Tube
- 推荐标准
- AS 1038.22-2000 (R2013) Coal and coke - Analysis and testing Higher rank coal - Mineral matter and water of constitution
- AS 1301.P201m-1986 Methods of test for pulp and paper (metric units) Kappa number of pulp
- AS 1301.P414m-1986 Methods of test for pulp and paper (metric units) Conditioning of paper for testing
- AS 1774.22-1985 Refractories and refractory materials - Physical test methods Bonding strength of refractory mortar
- AS 1807.22-1989 Cleanrooms, workstations and safety cabinets - Methods of test Determination of air barrier containment of laminar flow safety cabinets
- AS 2001.2.22-1986 Methods of test for textiles Physical tests - Determination of yarn slippage in woven fabrics at a standard stitched seam
- AS 2362.22-1993 Automatic fire detection and alarm systems - Methods of test for actuating devices Sound pressure level test
- AS 2400.22-1985 Packaging Closures
- AS 3730.22-1993 Guide to the properties of paints for buildings Concrete and masonry sealer - Solvent-borne - Interior/exterior
- ASTM D3550/D3550M-17 Standard Practice for Thick Wall, Ring-Lined, Split Barrel, Drive Sampling of Soils
- ASTM D3551-17 Standard Practice for Laboratory Preparation of Soil-Lime Mixtures Using Mechanical Mixer
- ASTM D3552-17 Standard Test Method for Tensile Properties of Fiber Reinforced Metal Matrix Composites
- ASTM D3554-20e1 Standard Specification for Track-Resistant Thermoplastic High-Density Polyethylene Insulation for Wire and Cable, 75 °C Operation
- ASTM D3556-23 Standard Guide for Deposition on Glassware During Mechanical Dishwashing
- ASTM D3557-17 Standard Test Methods for Cadmium in Water